Rayburn Royal Manual de usuario

1 Mk 2 PJ. CONVERSION © Rayburn Royal 11-05-04 INSTALLATION INFORMATION © http://www.oilstoves.co.uk/

10Fig 21 Tighten the fuel hose. Fit Control Module 2 x M5 fasteners. Fig 22 Before fastening the control module onto the upper support plate conn

11Fig 23 Adaptor plate fitted Fig 24 is a view showing access holes drilled through the inner casting. Fig 24 Fig 25 is a view showing some crit

12If the pipework is in contact with any sharp edges fretting can occur, to prevent this apply silicone sealant at any potential hazard points. Ch

1333.. LLIIGGHHTTIINNGG.. Make sure the appliance is fully assembled , do not fit the baffle box as it is necessary to view the flame. Carry ou

14Failure to ignite will cause the flame failure button on the controller to illuminate, after a short time push the button in to reset the controlle

15Because the burner is a tight fit in the ashpit area it will be necessary to ease the control module out of the ashpit on to a suitable temporary

1644..1111.. CCHHIIMMNNEEYY SSYYSSTTEEMM.. Chimney system should be checked to make sure that it complies with the relative standards, regulations

17The warranty covers PARTS ONLY for a period of ONE YEAR and is conditional upon all the requirements of our installation and commissioning instruc

18FFIIGG 2277 SSEECCTTIIOONNAALL DDEETTAAIILLSS FFIIGG 2288 BBOOAARRDD DDEETTAAIILLSS

19FFIIGG 2299 GGRRIINNDD DDOOOORR OOVVEENN SSTTAATT DDEETTAAIILLSS The oven stat is wired in series with the water stat (if it is fitted)

2Contents 1-8. See Separate Document._____________________________________ 4 11. Fitting The Kit._____________________________________________ 4 Remo

20Care must be taken when fitting the guide tube which is positioned so as to allow the subsequent, convenient replacement of the stat should it ever

21 WWIIRRIINNGG DDIIAAGGRRAAMMSS ((AALLLL SSTTAATT DDEETTAAIILLSS))

22CCHHIIMMNNEEYY TTEERRMMIINNAALL DDEETTAAIILLSS..

23 1199.. PPAARRTTSS AANNDD PPAACCKKIINNGG LLIISSTT Item No Description PART NUMBER Qty Check 1 Burner assembly complete 77-01-100 1 2

247 Cable entry plate 87-18-100/7 1 8 Fire valve bracket 87-18-100/8 1 9 Boxed oven stat assembly inc phial bracket 77-01-005/F 1 10

25This product is subject to continuous development and improvement and it is consequently acknowledged that due to this process there may be some o

34.3. Filter.__________________________________________________ 15 4.4. Site Glass or Tank Gauge. ___________________________________ 15 4.5. Oil li

411--88.. SSEEEE SSEEPPAARRAATTEE DDOOCCUUMMEENNTT.. 1111.. FFIITTTTIINNGG TTHHEE KKIITT.. RREEMMOOVVEE TTHHEE HHOOTTPPLLAATTEE.. CCHHEECC

5Fig 1 Shows bricks and riddling grate removed but the cast iron grate carrier still in place Fig 2 Shows the oven side castings, riddling grate,

6 Use silicone to attach the boards to the side castings. Fit Closure Plate Support Boards Fig 5 These are held in place by the angle brackets on t

7Fit Primary Closure Plate Cover Board Fig 8 Fit the two pieces of 200 mm long x 20 mm dia rope at the front and rear of the primary closure plate

8Fit Secondary Front Board Fig 12 When the secondary front board is fitted, fix it to the front board by the use of 4 x 35mm wood screws. Screw thr

9The burner base plate has a levelling screw in each corner, make sure that the plate sits flat on the base of the cooker. Push the burner base plat